How to install the WJ-12 railway fastener system

Jul 10, 2025 Leave a message

The WJ-12 type fastener consists of T-bolts, flat washers, nuts, elastic clips, insulated gauge blocks, gauge baffles, under-rail pads, iron tie plates, elastic pads under iron tie plates, preset height-adjusting pads and pre-embedded iron seats. In addition, for the need of adjusting the vertical position of the rail, it also includes height-adjusting pads under the gauge baffle.

 

 

Laying Sequence and Requirements for WJ-12 Type Railway Fastener System

 

 

Special reminder: When using this fastener, do not use the pre-embedded iron seats for sleeper position adjustment or track adjustment operations, so as to avoid damage to the pre-embedded iron seats.

 

Clean the mud and dirt from the rail-bearing surface of the sleeper between the two pre-embedded iron seats and the mortar inside the pre-embedded iron seats.

 

rail pad

 

Place the preset height-adjusting pad on the rail-bearing surface.

 

steel rail

 

Place the elastic pad under the iron tie plate in the middle position of the pre-embedded iron seat.

 

railway track

 

Place the iron tie plate on the elastic pad under the iron tie plate.

 

rail fasteners

 

Place the T-bolt on the pre-embedded iron seat.

 

railway fasteners

 

Install the gauge baffles of appropriate specifications on the pre-embedded iron seats according to the configuration table for left-right position adjustment of a single rail, and fix the T-bolts.

 

Rail type Lateral position adjustment range of a single rail (mm)) Outside of the rail Inside of the rail
gauge baffle insulated gauge block insulated gauge block gauge baffle
75kg/m -6 35 15 9 31
-4 35 13 11 31
-2 35 11 13 31
0 31 13 11 35
2 31 11 13 35
4 31 9 15 35
60kg/m -6 35 16 8 31
-4 35 14 10 31
-2 35 12 12 31
0 31 14 10 35
2 31 12 12 35
4 31 10 14 35

 

gauge block

 

Place the under-rail pad between the gauge baffles.

 

railroad fasteners

 

Clean the sludge from the rail bottom and lay the rail.

 

fastenering system

 

Place the insulated gauge blocks of appropriate specifications according to the configuration table for left-right position adjustment of a single rail.

 

heavy rail

 

Apply oil to the threaded part of the T-bolt, install the elastic clip, flat washer and nut, and tighten the nut to fasten the elastic clip. The fastening of the elastic clip is based on the contact between the front lower jaw in the middle of the elastic clip and the insulated gauge block, and the gap between them shall not exceed 0.5mm. At this time, the torque for tightening the nut is approximately 130N·m.

 

elastic clip

 

 

Installation and Adjustment

 

 

Lateral position adjustment of a single rail

 

This fastener allows the lateral position adjustment range of a single rail to be: -6mm ~ +4mm.

 

Check the gauge and rail alignment. If they do not meet the requirements, replace the gauge baffles and insulated gauge blocks with the ones of corresponding numbers according to the configuration table for lateral position adjustment of a single rail.

 

Adjustment of rail vertical position

 

The vertical position adjustment range of the rail for this fastener is -4mm ~ +16mm.

 

Check the vertical position of the rail. If it does not meet the requirements, the preset height-adjusting pad can be removed, the under-rail pad can be replaced, and the height-adjusting pad under the gauge baffle can be inserted. For specific configurations, refer to the configuration table of adjusting pads for the vertical position of the rail. For lowering adjustment, remove the preset height-adjusting pad and adjust by replacing under-rail pads of different thicknesses. The thickness of the under-rail pad should not exceed 11mm, and it must not be used in a stacked manner. The height-adjusting pad under the gauge baffle consists of two pieces, which are inserted from both sides of the sleeper respectively. During installation, the teeth should be engaged. The thickness should not exceed 11mm, and the number should not exceed 2 pairs. When the height adjustment amount is greater than 5mm, type II T-bolts shall be used.

 

Configuration Table of Adjusting Pads for Rail Vertical Position (Unit: mm)
Vertical position adjustment range of rail Thickness of under-rail pad Thickness of height-adjusting pad under gauge baffle Thickness of preset height-adjusting pad
-4 6 0 0
-3 7 0 0
-2 8 0 0
-1 9 0 0
0 6 0 4
'+1~+5 7~11 0 4
'+6~+10 7~11 5 4
'+11~+16 6~11 11 4

 

rail clip

 

GNEE RAILWAY RAILWAY is a professional trading company focusing on the export of railway fasteners, committed to providing reliable rail connection products for global railway construction projects. The main products include a full range of railway fasteners such as various spring clip fastener systems, sleeper bolts, anti-loosening washers and insulating components, which are suitable for various application scenarios such as conventional railways, heavy-duty railways and urban rail transit.

 

With rich international trade experience, we have established an efficient supply chain system and logistics network to ensure timely delivery of products. We insist on being customer-oriented, winning market recognition with high-quality products and services, and look forward to establishing long-term and stable cooperative relationships with global customers.