GNEE RAILWAY RAILWAY Steel (Tianjin) Co., Ltd. is one of the most reliable manufacturers and suppliers of Type II Clip Fastening System for 60 kg/m Rail in China, also supports customized service with low price. Please feel free to buy cheap Type II Clip Fastening System for 60 kg/m Rail made in China here from our factory.
What Is the Type II Clip Fastening System?
The Type II clip fastening system, known in Chinese practice as elastic-bar Type II fastening, is a bolted rail fastening used to press the rail foot firmly onto the sleeper, hold the gauge, and restrain vertical, lateral and longitudinal movement of the rail relative to the sleeper. It is designed for 60 kg/m (CHN60) rail laid as continuously welded track on prestressed concrete sleepers with shoulder.
Each elastic bar is pressed down by a screw spike or bolt threaded into the sleeper, which makes the Type II system a bolted configuration. This distinguishes it from the boltless Type III fastening of the same standard family, in which the clip is wedged by insulating gauge blocks and no bolt is used. The bolted arrangement of Type II gives maintenance crews a direct, verifiable clamping force on every rail seat and simplifies partial replacement of individual components.
System Composition
The table below lists the components of one rail seat (one rail at one sleeper) in a typical configuration per the TB/T 3065 assembly definition.
![]()
Type II clip fastening system: elastic bars, gauge baffles, gauge plate seats and rubber rail pad on a shouldered concrete sleeper.
| Component | Qty | Material / Type | Function |
|---|---|---|---|
| Type II elastic bar | 2 | 60Si2MnA spring steel (typical per standard) | Presses the rail foot; supplies the toe load and elastic deflection |
| Gauge baffle | 2 | Ductile iron QT450-10 (typical per standard) | Locates the rail foot laterally; gauge adjustment by number selection |
| Gauge plate seat | 2 | Nylon PA66 (typical per standard) | Seats the baffle on the sleeper shoulder; provides electrical insulation |
| Rubber rail pad | 1 | Rubber, about 10 mm thick | Provides vertical elasticity and damping; distributes rail load |
| Screw spike or bolt, with nut and flat washer | 2 sets | Steel (typical per standard) | Clamps the elastic bar and fixes the system to the sleeper |
Technical Parameters
Values below are typical design figures cited in industry technical references for the Type II system;
| Parameter | Typical value / remark |
|---|---|
| Applicable rail | 60 kg/m (CHN60) rail; continuously welded track preferred |
| Sleeper | Prestressed concrete sleeper with shoulder |
| Fastening type | Bolted: screw spike or bolt with nut and flat washer |
| Toe load per clip | Approx. 10 kN (typical design value per industry references for TB/T 3065) |
| Spring travel | Approx. 10 mm (typical design value per industry references) |
| Rail pad | 60-10 type rubber pad, about 10 mm thick |
| Gauge adjustment | Up to about ±8 mm, in 1 mm steps, by selecting gauge baffle numbers (typical; per standard) |
| Height adjustment | Small vertical adjustment by shims placed under the rail (typical) |
| Insulation | Nylon gauge plate seats insulate the rail from the sleeper shoulder, supporting track-circuit operation |
Typical Applications
- Upgraded (speed-up) and conventional-speed lines with 60 kg/m rail in continuously welded track - generally up to about 160 km/h class in Chinese practice (typical application; confirm with line design).
- Existing-line renewal and heavy maintenance works, where the bolted configuration allows straightforward tension verification and component-level replacement during track possession.
- Trunk and secondary lines requiring higher toe load than the Type I fastening and reliable holding under repeated wheel loading.
- Sections with sharp curvature or steep gradients where longitudinal and lateral restraint of the rail is critical (design values per standard).

Installed Type II fastening on 60 kg/m rail in continuously welded track.
Manufacturing and Quality Notes
The Type II elastic bar is formed from 60Si2MnA spring steel and heat-treated to the hardness and fatigue requirements of the standard; gauge baffles are typically ductile iron QT450-10 and gauge plate seats are nylon PA66. Production follows the inspection framework of TB/T 3065, which covers dimensional checks, material verification and assembly performance tests such as toe load and spring travel. Parts are supplied with traceable material certificates and test records so that buyers can cross-check each lot against the standard.
Frequently Asked Questions
Q1. Is the Type II system bolted or boltless?
Bolted. Each elastic bar is pressed by a screw spike or bolt with a nut and flat washer threaded into the sleeper. Within the same standard family, the Type III fastening is the boltless configuration.
Q2. Which rail section does it fit?
It is designed for 60 kg/m (CHN60) rail, typically laid as continuously welded track on shouldered prestressed concrete sleepers.
Q3. What is the toe load of one clip?
Approximately 10 kN per clip is the typical design value cited in industry technical references for the Type II elastic bar; confirm the exact value against the applicable revision of TB/T 3065.
Q4. How is the gauge adjusted?
By replacing the gauge baffles with a different number, the rail is shifted laterally in steps of about 1 mm over a typical range of up to ±8 mm (per standard/typical references).
Q5. What material is the elastic bar made of?
The elastic bar is typically 60Si2MnA spring steel, heat-treated to the hardness and fatigue requirements of the TB/T 3065 family.
Hot Tags: Type II Clip Fastening System for 60 kg/m Rail, China Type II Clip Fastening System for 60 kg/m Rail manufacturers, suppliers, factory, E clip Fastening System, J8 Heyback Spring Clip, 9 Types Of Rail Fastenings System, Railway Sleepers, KPO Clamp Rail Fastening System, J9 Heyback Spring Clip




