ASCE 80 Rail: Dimensions and Applications

Jan 23, 2026 Leave a message

What the ASCE Standard Covers

The ASCE rail specification is one of the oldest tee-rail standards, written by the American Society of Civil Engineers for light and medium-duty track. ASCE rails are characterized by a smaller cross-section and lighter weight than the AREMA series, and they are intended for low to medium axle loads: industrial sidings, crane runways, mining track and plant logistics. The size designation is the mass in pounds per yard, so ASCE 80 means 80 lb/yd, and the full set runs from ASCE 60 up to ASCE 85 and beyond into the heavier profiles. The same tee geometry is shared across the family, so fishplates and fasteners are designed per size. Although the specification is American, the profile is rolled worldwide, including in Chinese mills as U71Mn grade, which makes ASCE rails easy to source internationally.

ASCE 80 Dimensions and Mass

Parameter Value
Mass 39.68 kg/m, equal to 80 lb/yd
Rail height H 127 mm
Base width B 127 mm
Head width C 63.5 mm
Web thickness E 13.89 mm
Section area 50.55 square cm
Typical grade Q235B, U71Mn, carbon steel per ASTM A1

The wide head, 63.5 mm, distributes the wheel pressure over a large contact area, which matters for crane wheels with their narrow contact band. The base is as wide as the rail is high, 127 mm on 127 mm, which gives the rail a stable footprint on timber sleepers or steel beams. The web thickness of 13.89 mm is generous for a rail of this size, resisting the vertical shear from point loads under crane wheels. These are nominal section values from the standard, and the rolling tolerance follows the applicable delivery specification.

Typical Applications

Crane runways: overhead and gantry cranes in factories, ports and shipyards, where the rail must guide the wheel set under repeated point loads.

Underground mining: haulage track for materials and equipment, both permanent and temporary, where the light rail is easy to lay and re-lay.

Automated warehousing: rails for stacker cranes and automated guided vehicles that run on fixed paths.

Industrial transport: internal logistics track in steel plants, concrete plants and maintenance depots.

For all these uses the attraction of ASCE 80 is the balance between strength and weight: it carries the loads of heavy machinery but stays light enough to handle, transport and lay without heavy track machinery. On crane runways it is usually paired with a flat-bottomed seating on the steel girder and clamped with rail clips rather than ballast-anchored sleepers, which is why ASCE rail buyers typically order the matching clamping plates and fishplates at the same time.

Materials and Grades

ASCE rails are rolled from carbon steel to the requirements of ASTM A1 for tee rails, and in practice two material options dominate supply. Q235B, a common structural steel, is used where the loads are modest and cost is the priority, and it is easy to weld and drill for fishplating. U71Mn, the classic Chinese rail grade with a tensile strength of at least 880 MPa, is specified where wear and repeated loading matter, such as busy crane runways and mine haulage. For very heavy duty, head-hardened or alloy grades can be rolled to order, but for most ASCE 80 applications the standard grades are sufficient. The buyer should confirm the grade, the mechanical property certificate and the chemical composition report with the order, and the mass tolerance should be checked against the 39.68 kg/m nominal value on the delivered rails.

How ASCE 80 Compares with Adjacent Sizes

Profile Mass kg/m Typical use
ASCE 60 29.8 Very light plant track, small cranes
ASCE 80 39.68 Medium crane runways, mining, warehouses
ASCE 85 42.2 Heavier crane and plant track
BS 80A 39.76 British industrial track, similar mass
GB 38 kg/m 38.73 Chinese light industrial rail

The adjacent sizes are not interchangeable: the fishplate holes, the clamping plate contours and the rail foot width differ, so the whole set, rail, fishplates, clips and bolts, must be ordered for the same profile. When a project specifies ASCE 80, the rail alone is not enough; the matching joint bars and fastening hardware should come from the same source so the dimensions are controlled together.

Selection and Procurement Guidance

Choose ASCE 80 when the axle load stays in the light to medium band, the track runs in industrial plant rather than main line, and the rail must be light enough to handle by small gangs. For crane runways, verify the crane wheel load and the wheel spacing against the rail section capacity, and check that the clamping system is designed for flat-bottomed seating on steel. For mining and warehouse track, confirm the sleeper type and spacing. In procurement, request the dimensional certificate against the standard, the mass check, the material certificate with chemical composition and mechanical properties, and the fishplate and clip drawings. Since ASCE rails are rolled to an American specification but produced in multiple countries, the safest order specifies the profile, the grade, the mass tolerance and the inspection documents, and the supplier should confirm all four before production.

What does ASCE 80 mean in metric units?

ASCE 80 is the 80 lb/yd profile, which is 39.68 kg/m. Its main dimensions are a 127 mm height, a 127 mm base width, a 63.5 mm head width and a 13.89 mm web thickness.

What is ASCE 80 rail used for?

Overhead and gantry crane runways, underground mining track, automated warehouse rails and industrial transport. It suits moderate axle loads where the rail must be light enough to handle but strong enough for machine loads.

What is the difference between ASCE and AREMA rails?

ASCE is the older, lighter specification for industrial track, while AREMA covers the heavier main-line profiles such as 115RE and 136RE. Both are tee sections, but the dimensions, fishplates and fasteners are specific to each profile.

Which material grade should I order for ASCE 80?

Q235B for light duty and cost-sensitive projects, U71Mn for wear resistance under repeated crane or mine traffic. The mechanical property certificate and chemical composition should accompany the delivery.

Can ASCE 80 be welded or must it be fishplated?

Both are possible. Carbon steel grades weld reliably with the standard procedure, and fishplated joints are the traditional solution for industrial track. Welded track removes the joint maintenance but requires a qualified welding procedure and grind-back inspection.

Is ASCE 80 interchangeable with BS 80A?

No. Although the mass is similar, 39.68 versus 39.76 kg/m, the head, base and fishplate hole layouts differ. Order the complete set of rail, fishplates, clips and bolts for the exact profile specified on the project drawing.