SKL and Type II Railway Fastening Systems: Shared Principles, Components and Maintenance

Jul 01, 2025 Leave a message

Core Functional Parity

In a modern track structure the fastening system has one overriding duty: to hold the rail against the sleeper while still allowing the small elastic movements that the passing train demands. The SKL and Type II systems grew out of different design traditions and differ in clip geometry and shoulder arrangement, yet both answer the same load case. Under traffic the rail generates longitudinal forces from traction and braking, lateral forces in curves and vertical forces from axle loads, all acting cyclically on the fastening assembly.

Through the coordinated action of their components, both systems resist these forces to prevent rail displacement, maintain track gauge within the tolerance demanded by the operating speed, and keep the running surface regular enough for safe train operation. On ordinary mainline track the practical result is the same: stable rail support in which repeated train passage neither loosens the assembly nor opens the gauge.

Shared Component Architecture

The two designs converge on a common set of functional elements. The elastic clip is the core clamping part, deforming elastically to generate the toe load that presses the rail foot onto the pad. SKL systems use the SKL clip, while the Type II system uses a clip made from 60Si2CrVA spring steel to GB/T 1222; the geometry differs, but the clamping principle and the material family are the same.

Spiral spikes anchor the assembly into the sleeper and supply the reaction against which the clip works. Gauge adjusters, including gauge retainers and insulating blocks, allow fine adjustment of gauge during installation and routine maintenance. Rubber padding plates sit between rail and sleeper and perform two duties at once: they insulate the track circuit so that signalling current cannot leak away through the fastening, and they buffer impact forces, which reduces wear on the components and extends their working life.

Both families also include a rail seat interface that spreads the concentrated rail foot pressure over the sleeper surface, and both use insulating elements to keep the rail electrically separated from the reinforcement in the sleeper.

Comparable Performance Requirements

Because the duty is identical, the performance envelope specified for the two systems is closely comparable. Both must develop enough clamping force to resist rail creep and gauge widening under repeated axle passages, and to keep that force over the full maintenance interval rather than relaxing after a few weeks of traffic.

High strength is required to withstand long-term heavy loads, together with fatigue resistance in the clip itself, which works through millions of small deflection cycles. Both systems must also remain stable in extreme environments, from low winter temperatures that embrittle rubber and raise the risk of brittle fracture in steel, to high summer temperatures and sustained humidity that accelerate corrosion and ageing of elastomeric parts. On high-speed and heavy-haul lines with strict stability demands, both are specified to preserve the integrity of the track structure under high-speed, high-volume operation rather than merely to hold the rail in place.

Installation and Maintenance Practice

Installation of either system requires strict adherence to the specified fastener spacing, tightening sequence and toe load, because the clipping force achieved in the field determines whether the theoretical performance is realised. Power tools are set to a controlled torque or a controlled clip deflection so that the elastic clip is not over-stressed during assembly.

Routine maintenance follows the same logic on both systems. Patrols inspect components for wear and looseness, replace worn parts such as clips and pads, and retighten fasteners where spikes have lost preload. Staff monitor the clamping force of the clips, the tightness of the spikes and the ageing of the rubber pads, since a hardened or cracked pad both loses its buffering ability and degrades track circuit insulation. Where gauge has moved, the adjusters in either system allow correction without dismantling the assembly.

Component and Material Comparison

Function SKL system Type II system
Elastic clamping part SKL clip 60Si2CrVA spring clip to GB/T 1222
Anchoring element Spiral spike Spiral spike
Gauge control Gauge retainer and adjuster Insulating gauge block and adjuster
Rail seat interface Elastic rubber pad Elastic rubber pad
Primary duty Clamp rail, hold gauge, insulate circuit Clamp rail, hold gauge, insulate circuit

Frequently Asked Questions

Q: Are SKL and Type II fastening systems interchangeable?
They are not interchangeable part for part, because clip geometry, shoulder design and sleeper preparation differ. What they share is the functional principle, so the choice is normally decided by the track standard the line was built to.

Q: What is the core difference between the two clip designs?
The SKL clip and the Type II 60Si2CrVA clip differ mainly in geometry and in the way the clamping force is generated and retained, but both work by elastic deformation of spring steel to press the rail foot down.

Q: Why do both systems need an elastic pad?
The pad insulates the track circuit from the sleeper reinforcement and buffers impact forces, which protects both the sleeper and the fastener and lengthens the maintenance interval.

Q: Which maintenance checks apply to both systems?
Clamping force of the clips, tightness of the spikes, wear of clips and pads, and ageing of the rubber pad. Gauge is checked at the same time and corrected with the adjusters.

Q: Do both systems suit high-speed and heavy-haul lines?
Both can serve demanding lines when the correct class of clip, pad and spike is selected and the installation specification is followed, since the performance requirements placed on them are closely comparable.

Q: What ends the service life of an elastic clip?
Loss of clamping force through fatigue and stress relaxation, usually combined with corrosion or mechanical damage at the contact points, rather than a sudden fracture under normal track conditions.