Definition and Design Background of QU70 Crane Rail
QU70 is a hot-rolled crane rail profile defined in the GB/T 3426 series of crane rail standards. The designation QU70 refers to the head width of 70 mm. The section is 120 mm high with a 120 mm foot width and a thick web, giving a theoretical mass of 52.77 kg per metre. Compared with a mainline railway rail, the crane rail section is lower in height and wider in the head, a shape chosen for the operating conditions of overhead and gantry cranes: it must withstand very high wheel pressures at low speed, resist overturning moments from offset loads, and maintain alignment under frequent starts, stops and direction changes. The profile is rolled to full length and supplied with matching fishplates, bolts and crane rail clips for jointed installation.
Technical Parameters of QU70
| Parameter | Value |
|---|---|
| Rail head width | 70 mm |
| Rail height | 120 mm |
| Rail foot width | 120 mm |
| Web thickness | 28 mm |
| Theoretical mass | 52.77 kg/m |
| Typical supply length | 9–12.5 m |
| Steel grade | Medium-manganese steel with controlled hardness |
Main Application Scenarios
Ports: container terminals lay QU70 for rail-mounted gantry cranes (RMGs) and ship-to-shore cranes, where frequent heavy lifts demand a rail that resists deformation. Bulk terminals use grab cranes for coal and ore, and QU70 absorbs the repeated impact and wheel pressure of grab operation. Port logistics parks run mixed fleets of RMGs and tyre-mounted gantry cranes (RTGs) over large areas, and the rail provides a stable running surface that supports fast cargo transfer.
Mines: open-pit coal and iron mines use large mining cranes for equipment installation, repair and temporary ore lifting. QU70 copes with the harsh environment, temperature range and terrain of open-pit sites. In underground mines, the rail is laid to the tunnel layout and its high strength and wear resistance suit wet, dusty conditions where lighter rails would wear quickly.
Metallurgical plants: in hot rolling shops, cranes carry heated billets to the mill and finished sections to cooling and storage areas; QU70 withstands the weight of hot steel and the impact of frequent lifting. In cold rolling shops, precise positioning of coil and roll handling is supported by the dimensional stability of the rail, while its wear resistance suits the high running frequency.
Machinery manufacturing: workshops building ship engines, heavy machine tools and large presses lift components of tens to hundreds of tonnes. QU70 carries these loads without permanent set. In automotive plants, stamping die and body-panel handling benefits from the accurate running surface, and wear resistance matches the high duty cycle of production lines.
Selection and Installation Points
Selecting QU70 rather than QU80, QU100 or QU120 is a wheel-load and crane-duty decision: the heavier profiles are specified as crane capacity grows, while lighter cranes on P-type light rails or hot-rolled railway rails can reduce equipment cost. The rail must be installed with matching components: crane rail fishplates at the joints, and crane rail clips or spring clips on the sleeper or girder side. Joint gaps should follow the supplier's recommendation for the ambient temperature range, and the rail top surface must be aligned within the tolerance specified by the crane manufacturer, because wheel flange wear and crane vibration are direct consequences of poor alignment. The rail foot should sit on a continuous bearing surface, typically a steel girder or closely spaced sleepers, never on widely spaced supports.
Common Misconceptions
A frequent mistake is treating QU70 as interchangeable with a mainline railway rail of similar mass. The foot and head geometry differ, so standard railway rail clips do not fit, and the wheel profile of a crane is not compatible with a railway rail head. Another misconception is that any heavy rail can carry a large crane: the decisive property is not total mass but the wheel pressure distribution, which is why the crane manufacturer's wheel load specification, not habit, should decide between QU70 and heavier crane rail sections. Finally, QU70 does not require continuous welded installation; jointed track with properly maintained fishplates and clips is the normal, accepted practice for crane rails, provided joints are kept tight and shimmed against settlement.
Frequently Asked Questions
What does QU70 stand for?
The designation follows the GB/T 3426 crane rail series, where QU denotes a crane rail and 70 is the nominal head width in millimetres.
What is the theoretical weight of QU70 rail per metre?
52.77 kg per metre. The practical weight varies slightly with rolling tolerances.
Which cranes typically run on QU70 rail?
Container gantry cranes, grab cranes at bulk terminals, mining cranes, workshop cranes in metallurgical and machinery plants, and automotive plant cranes with moderate to heavy duty cycles.
What is the difference between QU70 and P-type light rails?
P-type rails are lighter, cheaper and easier to install, but their lower section modulus suits only light and small cranes. QU70 is used where wheel pressures and duty cycles are higher.
Can QU70 rail be used for mainline railway tracks?
No. The head and foot geometry, steel composition and hardness are designed for slow-speed, high-pressure crane operation, not for railway wheel profiles or high running speeds.
What lengths is QU70 rail supplied in?
Typical supply lengths are 9 to 12.5 metres, with fishplates, bolts and clips available as matched accessories for jointed installation.

