SKL-12 Rail Fastening System: Structural Features and Components

Aug 20, 2025 Leave a message

1. System Overview

The SKL-12 fastening system belongs to the SKL family of elastic rail fastenings, which also includes SKL 3 and SKL 14 variants. SKL-12 is a separate rail fastening system designed for ballastless track: the base plate is not tied to a concrete retaining shoulder, and each component is fixed separately to the sleeper or track slab. The system secures the rail against vertical, lateral and longitudinal forces, transmits load to the slab, and provides electrical insulation and vibration damping through its pad and plastic components.

The key structural principle is separation of functions. The elastic clip supplies the clamping force; the ribbed base plate distributes the load and locates the clip; the screw spike anchors the assembly to the slab; the dowel protects the spike thread in the concrete; the guide plate positions the rail foot laterally; and the rail pad provides elasticity and insulation between rail and plate. Because each function is carried by a dedicated, replaceable component, inspection and maintenance are simple and the system can be adjusted after installation.

2. Component Structure and Materials

Component Pieces per set Material Size / Note
SKL tension clip 2 60Si2CrA, 60Si2Mn or 38Si7 spring steel Available as SKL1, SKL3, SKL12, SKL14; hardness 42-47 HRC; 5 million cycles without breaking; to DIN 17221 and GB/T 1222
Screw spike 2 Grade 4.6 Q235, Grade 5.6 35# steel, Grade 8.8 45# steel M24×150 mm; to ISO 898-1 and UIC 864-1
Flat washer 2 Q235 Sized for M24 screw spike; to EN 10025 / EN 10139
Plastic dowel 2 HDPE or reinforced nylon PA66 Inserted into the concrete sleeper to protect the spike thread
Guide plate 2 Reinforced nylon PA66 For UIC54, UIC60, 50 kg/m and 60 kg/m rails; other sections on request
Rail pad 1 EVA or rubber Under-rail elastic and insulating pad

3. Adjustment Mechanisms

Ballastless track cannot be realigned by tamping, so the fastening system must provide all geometric adjustment. The SKL-12 achieves this with three mechanisms:

Horizontal and lateral adjustment: different sizes of eccentric taper pin are inserted between the guide plate and the ribbed plate to shift the rail sideways in defined steps. Swapping the pin for the next size moves the rail by the corresponding increment, typically 1-3 mm per step.

Vertical adjustment: high and low setting plates of different thicknesses are inserted under the rail or under the base plate to raise or lower the running surface, compensating for slab casting tolerances and track settlement.

Longitudinal restraint: the elastic clip presses the rail foot against the ribbed plate through the guide plate, generating the longitudinal resistance that controls rail creep. If a lower longitudinal resistance is required for expansion management, the rail pad and clip combination can be selected accordingly.

Because adjustment is made by exchanging standard parts rather than machining or shimming loose steel, the system remains fully tightened at every stage and the adjustment is repeatable and documented.

4. Performance Characteristics

The mechanical requirements of the SKL-12 are defined by the spring steel specification and the clip geometry. The clip is quenched and tempered to 42-47 HRC, which gives the elastic recovery needed to maintain clamping force under repeated wheel loads, and it is fatigue-tested to 5 million cycles without fracture. The screw spike and bolt assembly follow ISO 898-1 property classes, and the complete fastening is designed to hold the rail in gauge within the tolerances required for slab track. The ribbed plate and plastic components are selected so that the system provides the insulation resistance and dynamic stiffness expected for ballastless track on high-speed and metro lines.

Standards referenced in the design include DIN 17221 and GB/T 1222 for the spring steel, ISO 898-1 for the fasteners, UIC 864-1 for the spike dimensions, and EN 10025 / EN 10139 for the plate and washer material. Buyers should request the clip hardness certificate and the fatigue test report together with the dimensional inspection certificate.

5. Application and Installation Points

SKL-12 is normally used in ballastless track - slab track for high-speed lines, metro depots and tunnels - where there is no concrete retaining shoulder. Before installation, check that the dowel is fully seated in the sleeper, that the rail pad is centred under the rail foot, and that the guide plate is the correct size for the rail section. Tighten the T-bolt nut to the specified torque so that the clip deflects to its working position; under-tightening leaves the clip loose and accelerates wear, while over-tightening can overstress the clip beyond its elastic range. After the first weeks of traffic, re-check the clamping force and torque, because initial settlement in the dowel and pad is normal. During inspection, look for clip fatigue cracks at the toe and heel, pad wear or extrusion, and damage to the dowel mouth, and replace components individually as required.

6. Common Misconceptions

One misconception is that SKL-12 and SKL-14 clips are interchangeable. The clips differ in geometry and clamping force, and the guide plate, pad and T-bolt must match the clip type and the rail section; mixing types leads to incorrect clamping and premature fatigue. Another is that the plastic dowel is a sacrificial part that can be omitted when the spike is screwed directly into concrete - in fact the dowel protects the thread and allows the spike to be replaced repeatedly without damaging the sleeper, and omitting it destroys the anchorage. A third is that eccentric pins are only for initial alignment; they are the permanent lateral adjustment mechanism, and their sizes must be recorded so that maintenance can restore gauge without re-drilling.

FAQ

Q1: What does "separate" mean in a separate rail fastening system?
It means the base plate is fixed to the sleeper or slab independently and there is no concrete retaining shoulder holding the rail; each component is installed separately.

Q2: How much lateral adjustment does the SKL-12 system allow?
Lateral adjustment is achieved by exchanging eccentric taper pins of different sizes, typically shifting the rail in steps of about 1-3 mm per pin size within the system's design range.

Q3: How is vertical adjustment performed on ballastless track?
By inserting setting plates of different thicknesses under the rail or base plate, which raises or lowers the running surface to compensate for slab tolerances.

Q4: Which rail sections does SKL-12 support?
Commonly UIC54 and UIC60, and 50 kg/m and 60 kg/m national rails; other sections can be supplied with matching guide plates and pads.

Q5: What are the clip acceptance criteria?
Hardness 42-47 HRC and 5 million fatigue cycles without fracture, verified against DIN 17221 and GB/T 1222 with the corresponding test certificates.

Q6: Can SKL clips be reused after removal?
Clips should be inspected for cracks, permanent deformation and coating damage before reuse; a clip that has been over-deflected or shows fatigue cracks must be replaced.