Two Fastening Families, Two Design Philosophies
Ballasted mainline track depends on a fastening assembly to hold the rail at the correct gauge, transfer vertical and lateral loads into the sleeper, and preserve the electrical separation that track circuits rely on. The Type V and Type IV systems are both widely deployed for this duty, yet they were engineered around different sleeper designs and different maintenance models. Choosing between them is therefore a track engineering decision rather than a purchasing preference.
This comparison examines the four points that govern interchangeability: structural design, elastic clip family, gauge adjustment hardware, and measured mechanical performance.
Structural Design: Shouldered Bolted versus Shoulderless Boltless
The Type V assembly is a shouldered, bolted design. The elastic clip is held down by a spiral spike passing through a sleeve, while a cast-in concrete shoulder carries the lateral load and prevents the rail from spreading. Because the connection is mechanical, individual components can be dismantled and reassembled during routine inspection, which suits lines maintained with hand tools or light equipment.
The Type IV assembly removes both the shoulder and the bolt. The elastic clip is inserted directly into a pre-embedded iron seat and clamps the rail base by its own elasticity. Eliminating the bolt also eliminates the bolt-loosening failure mode, reducing the number of components that must be torque-checked and the risk of a fastening point relaxing between maintenance cycles.
Type V: shouldered, bolted, fully dismantlable, lateral restraint provided by cast-in concrete shoulders.
Type IV: shoulderless, boltless, fewer wearing parts, lateral restraint provided by the clip and the pre-embedded iron seat.
Elastic Clip Types and Contact Behaviour
The clip is the component that actually generates clamping force, so the two systems draw on different clip families and different contact principles.
| Item | Type V | Type IV |
|---|---|---|
| General section | W2-type clips | C4-type clips |
| Special sections | X3-type clips for low-resistance bridge sections | JA-type and JB-type clips for rail joints |
| Force generation | Three-point contact, giving a uniform clamping force distribution along the clip footprint | Elastic deformation of the clip against the rail base |
Three-point contact spreads the load and lowers local stress concentration in the rail base, which is why the Type V clip reaches a higher force. The elastic route used by the Type IV clip prioritises assembly simplicity and repeatability, and it pairs naturally with low-restraint track on bridges.
Gauge Adjustment Components
| Item | Type V | Type IV |
|---|---|---|
| Adjusting component | Engineering plastic gauge retainer | Insulated gauge block |
| General section | No. 2 to No. 8, seven specifications | G4, seven specifications |
| Rail joint | Same retainer family | G4J, seven specifications |
| Adjustment increment | 2 mm | 1 mm |
The finer 1 mm increment of the Type IV system allows tighter gauge correction, which is useful on curves and wherever track geometry must be tuned after tamping. In both designs the plastic component also provides the electrical insulation between rail and sleeper that track circuits depend on, so dielectric strength and ageing resistance matter as much as the dimensional step.
Mechanical Performance Side by Side
| Performance index | Type V | Type IV |
|---|---|---|
| Clamping force, general section | ≥11 kN | ≥8 kN per clip |
| Longitudinal resistance, general section | ≥9 kN | ≥9 kN per fastener set |
| Assembled clamping force, general section | Not specified as a set value | ≥20 kN |
| Bridge section | ≥6 kN clamping force and longitudinal resistance of about 4 ± 1 kN | Combined with low-restraint track components |
The numbers show a clear trade-off. On plain track the Type V clip is the higher-force component, while the Type IV assembly reaches comparable longitudinal resistance with a lower force per clip because the load is shared differently across the assembly. On bridges the design intent reverses: the Type V system deliberately reduces clamping force and allows controlled longitudinal movement, so the track does not fight the structure.
Application Scenarios and Specification Steps
Type V matches shouldered prestressed concrete sleepers on ballasted track, and it is the usual choice for conventional lines operated at roughly 160 to 250 km/h, including corridors that carry both passenger and freight traffic. Type IV matches shoulderless concrete sleepers on ballasted track and is optimised for lines where heavy on-track machinery performs tamping and surfacing.
A practical selection sequence for a new section or a re-railing package:
Confirm the sleeper family and whether cast-in shoulders are present.
Identify which tamping and maintenance machines work the section.
Confirm design speed and the passenger to freight traffic mix.
Compare the required gauge adjustment range against the 2 mm or 1 mm increment.
Review bridge and joint locations, where low-resistance or joint-specific clips are required.
Verify material and dimensional certificates for clips and insulating parts against the project specification.
Frequently Asked Questions
Q: Can a Type V clip be installed in a Type IV assembly?
No. Clip geometry, the bearing surface on the rail base and the anchoring hardware differ, so clips from the two systems are not interchangeable.
Q: Which system suits a high-speed line?
Both appear on modern ballasted track, but the decision follows the sleeper design and the design speed. The Type V system is normally paired with shouldered prestressed concrete sleepers at speeds in the 160 to 250 km/h band.
Q: Why does the Type IV system offer a 1 mm gauge increment?
Its insulated gauge blocks are supplied in seven specifications stepping by 1 mm, so geometry can be corrected in finer increments without changing the clip or the sleeper.
Q: What does the plastic gauge component do besides adjust gauge?
It insulates the rail from the sleeper, which is essential for track circuit operation, and it must resist ageing, moisture and repeated compressive load.
Q: How does bridge track change the fastening requirement?
Bridge sections need lower longitudinal restraint so that rail forces can be released in a controlled way. The Type V general section provides ≥11 kN clamping force, while the bridge section variant is specified at ≥6 kN with longitudinal resistance around 4 ± 1 kN.
Q: What should be verified when a batch of fastenings is delivered?
Check clip dimensions and force, gauge component specifications and insulation performance, plus material certificates, so that the delivered assembly matches the fastening type specified for the line.

