GB heavy rails are the rails defined by Chinese national standards for the sections that carry heavy axle loads and dense traffic. The definition is not based on weight alone. A heavy rail exists because the track must withstand the concentrated pressure, bending and impact generated by heavy haul freight, high speed passenger trains and metro traffic, so material grade, section geometry, dimensional tolerance and delivery condition are all fixed by standard rather than by individual project preference.
What Actually Defines a Heavy Rail
The accepted dividing line in Chinese practice is the rail mass per metre. Light rails are the smaller profiles covered by GB/T 11264 and used for temporary lines, industrial sidings and maintenance work, while heavy rails begin at 43 kg/m and run through 50 kg/m, 60 kg/m, 75 kg/m and larger sections. The governing product standard is GB/T 2585, supported by TB/T 2344.1 for railway rail delivery technical conditions. For comparison, the same class of product is covered internationally by EN 13674-1 for Vignole rails of 46 kg/m and above.
Definition also depends on quality attributes rather than geometry alone. A heavy rail must be produced from a specified rail steel grade, fully killed and continuously cast, rolled to a controlled profile, straightened, and supplied with defined limits on surface defects, internal soundness, residual stress and hardness distribution across the head. Two rails with identical 60 kg/m profiles are not interchangeable if one of them misses those requirements.
Heavy Rail, Light Rail and Crane Rail Compared
| Product | Typical mass per metre | Principal use |
|---|---|---|
| Light rail (GB/T 11264) | Up to about 30 kg/m | Industrial sidings, temporary track, mining and plant service lines |
| Heavy rail (GB/T 2585) | 43 kg/m to 75 kg/m | Trunk railways, heavy haul freight, high speed and metro track |
| Crane rail (QU series) | QU70 to QU120 type sections | Bridge cranes, gantry cranes and heavy handling equipment runways |
The three families differ in head shape and in the way load is transferred. Crane rails have a wide, flat head and a heavy web so that the wheel load spreads over a larger contact area, while railway heavy rails use a head profile that matches the wheel tread and flange. Buyers should not substitute one family for another, even when the mass per metre appears similar.
Grades Used in GB Heavy Rail
Chinese heavy rails are supplied in rail steel grades such as U71Mn, U75V and U78CrV, with the high speed and premium variants specified in the delivery technical conditions for those applications. The grade letter U identifies rail steel, the number gives the nominal carbon content in ten thousandths, and the following letters indicate the alloying concept, so U71Mn is a plain carbon manganese rail steel and U75V and U78CrV are vanadium or chromium alloyed grades with higher hardness and wear resistance.
Selection follows the duty. Plain carbon grades remain the workhorse for general trunk lines and metro track, while alloyed and heat treated grades are chosen for curves, heavy haul lines with high axle loads and grinding regimes, and for crossings and switches where wear is concentrated. Commonly quoted minimum tensile strength levels are around 880 MPa for U71Mn class and around 980 MPa for U75V class, with elongation of about 9 to 10 %, so the rail can yield locally without brittle fracture.
Where Heavy Rails Are Used
The scope of heavy rail is wider than a single railway category. Inter-regional trunk lines planned as heavy haul corridors, high speed lines, intercity passenger railways and urban rail transit all depend on heavy rail sections as their structural basis.
Heavy haul freight corridors use 75 kg/m or 60 kg/m rails where axle loads and annual tonnage are highest, and welded strings are standard.
High speed lines use long, straight, tightly toleranced 60 kg/m rails produced to the rail delivery technical conditions for that duty.
Intercity railways carry mixed passenger traffic and require a rail with stable geometry to keep ride quality consistent at speed.
Metro and urban rail systems rely on heavy rail because short headways and high volumes generate cumulative wear in tunnels and on elevated structures.
Busy mixed traffic corridors illustrate the point. On a north south trunk artery such as the Beijing to Guangzhou line, passenger trains and heavily loaded freight trains share the same rails, so the rail must absorb frequent impact loading without developing fatigue damage. In urban systems, the high passenger volumes of a metro network impose demanding requirements on track stability and on the consistency of the rail surface, because maintenance windows are short and service interruptions are costly.
How Heavy Rail Is Specified and Delivered
Ordering follows a short checklist. First, fix the section and the steel grade, then state the delivery condition, whether as rolled, head hardened or otherwise heat treated. Next, define the length: standard heavy rails are increasingly ordered in 25 m or 100 m welded strings or in long lengths for flash butt welding on site. Finally, specify end drilling, bolt hole positions and the acceptance requirements for surface quality, internal soundness and straightness.
The rail must also be traceable. Heat number, casting number and rolling identification let the track engineer link a rail in service back to its production route, which is what makes it possible to manage grinding, welding and replacement decisions on a heavy haul line with confidence.
Frequently Asked Questions
Q: Is heavy rail defined only by its weight per metre?
No. The mass per metre identifies the section family, but the definition also requires a specified rail steel grade, standard dimensional tolerances, internal soundness and a controlled delivery condition.
Q: What is the difference between heavy rail and light rail?
Light rail covers the smaller profiles under GB/T 11264 for industrial and temporary track, while heavy rail starts at 43 kg/m under GB/T 2585 and is intended for trunk, heavy haul, high speed and metro lines.
Q: Which grades are commonly used for GB heavy rails?
U71Mn for general trunk and metro track, and U75V or U78CrV where higher hardness and wear resistance are needed on curves, heavy haul lines and other high wear locations.
Q: Can crane rail be used as railway heavy rail?
No. Crane rail sections such as the QU series have a flat head designed for crane wheels, so they should not be installed in railway track even where the mass per metre looks comparable.
Q: In what lengths are heavy rails delivered?
Common practice is 25 m or longer lengths for site welding, and 100 m welded strings where transport and handling allow; the length and welding method should be stated in the order.
Q: How does GB/T 2585 relate to EN 13674-1?
Both standards define rails for the same class of track duty, but they use different section series, grade designations and tolerance tables, so a rail qualified to one standard is not automatically interchangeable with a rail qualified to the other.

